CAN I SET UP A BATHTUB MYSELF? FACTORS TO CONSIDER AND ACTIONS

Can I Set Up a Bathtub Myself? Factors to Consider And Actions

Can I Set Up a Bathtub Myself? Factors to Consider And Actions

Blog Article

About

They are making a number of great points on How to Install a Bathtub as a whole in this content following next.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough project. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open up a wall to remove the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have currently gotten a new bathtub and do not require to alter the setup of your previous water system pipes.
Your devices and product checklist must comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
    Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic due to the restricted access that is frequently the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
    Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

    Mounting the Tub


    Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny factors.
    The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub till the level reads degree.
    To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
    Activate the water system as well as examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally check the overflow electrical outlet and the regular outlet for leaks.
    Lastly, fix the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait till the bathtub has actually been used at the very least when as this will resolve it into its last position.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines remain in location in between the tap as well as the sink. Secure the faucet in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind should be linked to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split an inflexible seal, causing the water to permeate the wall in between the bathroom and the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the tub remains in usage. The sealer can split rather very early if you do not take into account this activity prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    As a passionate reader on Installing A Bathtub, I assumed sharing that excerpt was worthwhile. Make sure you take a moment to distribute this blog posting if you appreciated it. I value reading our article about How to Install a Bathtub.




    Schedule A Service


    Report this page